Materials to Maintain Your ZHP IIIII Hand Protection IIIII Tools to Maintain Your ZHP
Amazon Link for ZHPMafia ZHP
Amazon Link for ZHPMafia ZHP
Amazon Link for ZHPMafia ZHP
Results 1 to 8 of 8
  1. #1

    Rear Electric Sun Blind Retrofit

    I have not seen any complete step a – z rear sunshade retrofit guides and decided to post this DIY outlining how I installed an electric rear sunshade assembly into my ZHP sedan and make this guide so that anyone could follow this to install an electric rear sunshade into a coupe. One thing to note is that sedans have an outline molded onto the back of the rear parcel deck shelf so it is very easy to cut out whereas on coupes the outline is drawn so it might not be complete. I will add there have been videos on how the retrofit is done on sedans and coupes however they do not detail now to run wiring from the rear passenger side of the deck shelf to the back of the center console switch unit where the wiring plugs into, and those DIYs don’t tell you what you need to source by part numbers whereas this one does.


    Disclaimer: By using this DIY on your BMW, I am in no way held responsible for any mishap you may incur while working on your car. You accept full responsibility for your BMW when using any portion of this DIY.

    Parts List:

    The following will be needed to install the electric rear sunshade assembly into your coupe or sedan:
    - 51-46-8-202-185: Sun Blind (electric sunshade assembly for sedan)
    - 51-46-8-223-046: Sun Blind (electric sunshade assembly for coupes)
    - 67-65-6-916-270: Motor used for electric sunshade (coupes and sedans)
    - 51-46-8-218-275: End Caps for electric sunshade (Left side)
    - 51-46-8-218-276: End Caps for electric sunshade (Right side)
    - 61-31-6-925-512: Center Console Switch Unit w/ elec sun shade button (coupes and sedans)
    - 07-14-9-149-399: Fillister Head Screw (you need 3 to secure the sunshade assembly to the rear parcel shelf)
    - 61-31-6-925-512: Switch Unit (heated seats/DSC/HK Stereo/TPMS/Sun Shade)
    - 51-46-8-218-275: SunBlind Rear Covering (left)
    - 51-46-8-218-276: SunBlind Rear Covering (right)
    - wiring needed for the wiring harness you need to make (about 13 foot of cabling - measure for a more accurate application for your car)
    - pins that fit inside the plug that connects to the back of the switch module at the center console just above the ash tray
    - Fresh cutting disks for Dremel (if used for this retrofit)
    - Roll of duct tape

    Notes:

    The rear sunshade assembly can be purchased hence the part numbers listed above or you can try sourcing them thru other means. In my case, I sourced a complete rear sunshade assembly thru eBay and got mine from Riga, Latvia. I paid $200 for my sunshade assembly shipped so no complaints. Brand new you will pay just over $700 for the sunshade assembly w/o motor, the motor will cost you another $250. These pop up on eBay as a complete unit from time to time from Europe.

    The switch unit that houses the Heated Seats, DSC, TPMS and Sunshade switches however, do not pop up on eBay nearly as often, if ever, so I sourced mine from ECS Tuning for $258.24 rather than wait for a used one to pop up on eBay. Other items that I needed to source were fresh cutting disks for my Dremel so I can make the cut needed to fit the sunshade assembly into the rear deck shelf. I also purchased matte black fabric spray paint so that I could properly refresh the deck shelf while it was out.

    Preparation is key to an OEM finish when done with this retrofit. After making the necessary cut on the rear deck shelf, I recommend taking some duct tape and go over the surface of the deck shelf to remove any loose debris from the surface before refreshing it using the matte black fabric spray paint. The finish will come out so much better if you take the time to clean off the rear shelf.

    Process:

    - RUNNING THE WIRING HARNESS

    1. Making the wiring harness. You are running a new wiring harness (two wires) from the back of the rear deck shelf to the back of the center console switch unit so making a wiring harness with some excess length is better than coming up short. I made mine about 13 feet in length then used BMW Cloth tape to make my wiring harness as close to OEM looking as I could. When done it will look something like this:


    In order to get the proper fitting pins needed to insert into pins 14 and 15 on the plug side of the wiring harness I sourced another switch module which had the plug and wiring that was cut from the car it was installed in just so I could reuse the pins needed for this retrofit. I am not sure the exact part number for these pins so for me it was just easier to source a module with the plug intact to pull the necessary pins from.



    So after I got the pins I wanted this is how it looked... I also got a third wire out because I will also be retrofitting TPMS into my ZHP per Jon's (JupiterBMW) DIY.


    2. Running the wiring harness into the car.

    You can start at either end here. I chose to run mine from the back going to the front along the passenger side.

    Pictured below is another angle showing how I'm running the wiring harness from top to the floor along with the existing wiring loom to the front.

    I fed the wiring harness along the wiring loom behind the B-pillar covering and up to the glove compartment. Once I got to this point, I ran the wiring harness behind the trim and up and across under the fuse assembly over to the center console.

    You can see by the yellow x's (in the picture below) how I ran my wiring loom over and across the glove compartment to the center console... this is also where I took up any extra slack in my wiring harness and looped it up.

    The next part was to insert the wiring into pin 14 (yellow wire) and pin 15 (white wire) into the plug pictured below then close up the plug and then put everything back together.

    It is now time to add the new switch module to the car . . .

    When you're done this is how it will look


    Routing the rear sun shade wiring harness is now complete.

    - MAKING THE CUT ON THE REAR DECK SHELF

    You're going to make a mess here. Do this in a ventilated area so you won't have to breathe the dust this will create when you are making this cut. Take your time as the rear deck shelf becomes real flimsy once the cut is made. You will see what I am talking about once you do this. Just take your time and be careful. While making the cut I found using my Dremel to be one of the easiest tools to do this.

    On sedans the back of every deck shelf has a marking similar to what you see in the picture above where to make the cut for the rear electric sun shade assembly to fit into. All you have to do is just follow the line to make the cut. This is why I found using a Dremel with a fresh cutting disk to be very handy in this case. Keep in mind you're making this cut and on the other side is a fabric covering for the rear deck shelf... why taking your time making this cut is so important. You don't want to rip the material on the other side while making this cut. The Dremel seems to be the best tool for making a clean precise cut.

    As you make the cut across the deck shelf it starts to bind just a little so I used some duct tape to secure the part that was cut to keep everything stable while making the rest of the cut. It worked out very well. Once the cut has been made use duct tape to go over the entire surface of the deck shelf to remove any dust and debris before respraying the deck using matte black fabric spray paint. The difference is huge as shown below.

    - REFINISHING THE REAR DECK SHELF - INSTALLING ELECTRIC SUNBLIND





    No more purple rear deck shelf.... When inserting the rear sunshade assembly into the rear deck shelf TAKE YOUR TIME fitting it into the shelf. It will fit in and you have to press the deck shelf into the grooves of the sunshade assembly and it will all fit in. Leave a little space on either side so lightly fit first then press in. You need to have even gaps on both edges so that the end caps will properly fit completing the look once installed.

    You can see in the picture above the gap at the end I am talking about. This is where the end cap installs into.
    When installed this is how the end caps look.


    The end caps and part numbers for them:
    - 51-46-8-218-275: SunBlind Rear Covering (left)
    - 51-46-8-218-276: SunBlind Rear Covering (right)


    And that's pretty much it. Once you have it installed and everything has been connected you can use the sun shade button at the center console to raise and lower the rear sun shade. It is a nice option to have in places where you are not allowed to have window tint on your car.


    - SECURING REAR SUN BLIND ASSEMBLY TO CAR

    You will need three Fillister screws to secure the rear sun blind assembly to the car. As is, you are able to secure the sun blind assembly at the center screw as this is easily accessible. In order to do the driver's side and Passenger's side you will need to drop the rear subwoofer enclosures then you will have access to fully secure the rear sun blind assembly.

    This is what the Fillister screws that are used to secure the rear sun blind look like.

    - OPTION SETP

    I left this part as the last part for this retrofit because you may need to or you may not need to do this. It all depends on the condition of your speaker grills in back. Also some have desired to make the bright silver Harmon Kardon strips black instead of bright silver to reduce the reflection of those strips on the rear glass... This is the time to do this. In my case I chose to refresh those strips to clean up everything back there.

    The condition of my strips were so aweful that I could use a greenie (light abrasion cloth) and water to remove what was left on them to get them fully black...


    This is what those strips look like with paint removed. They are plastic so be careful when removing paint from them. I used this paint when repainting my strips . . .

    I had is around and figured why not? I liked the results.


    - CONCLUSION and CREDITS

    The end result is what I have been wanting for a daily driver sedan. The finish looks completely OEM and is a feature not many have on their E46 BMWs. I have found it very nice to have especially with idiots driving with their high beams on... this really does a great job reducing the glare. To me a worthwhile retrofit.



    CREDIT: Shawn Robertson was very helpful to me in doing this retrofit to my ZHP. He has done this retrofit to his M3 Sedan and this is what gave me the idea of pursuing this retrofit. My thanks to Shawn for always getting back to me with the questions I have had.

    It is my hope that those of you who do this retrofit to your BMWs will find this DIY guide helpful.
    Last edited by cakM3; 01-26-2024 at 11:55 AM.

  2. #2
    Join Date
    Jul 2011
    Location
    Toronto
    Posts
    735
    BRAVO!!! this is an amazing detailed DIY

    -Daniel
    OEM BMW Performance (Missing cams and seats)
    LEVEL ONE // Euro Techniks
    Auto -> 6 Speed complete

  3. #3
    Join Date
    Jul 2011
    Location
    Wellesley, Ma
    Posts
    556
    Amazing work as always Charlie! Now locating those parts....

  4. #4
    Great writeup, I appreciate the time you took to document everything and do such a thorough job on the DIY.

    I don't think I've ever seen one of these sun shades in person but I've seen them on some youtube videos. I always thought they were really cool how they scissor open.

    Did the US even get these as an option, or was it Euro market only?

  5. #5
    Quote Originally Posted by kakashi169 View Post
    BRAVO!!! this is an amazing detailed DIY
    Appreciate your kind worlds Daniel, thanks!!

    Quote Originally Posted by sna77 View Post
    Amazing work as always Charlie! Now locating those parts....
    Appreciate it Steve! You have written up some awesome DIYs yourself and your last ZHP was the gold standard I have always tried to bring mine up to

    Quote Originally Posted by ///Mark_D View Post
    Great writeup, I appreciate the time you took to document everything and do such a thorough job on the DIY.

    I don't think I've ever seen one of these sun shades in person but I've seen them on some youtube videos. I always thought they were really cool how they scissor open.

    Did the US even get these as an option, or was it Euro market only?
    Thanks! Appreciate your kind words As for whether or not US spec BMWs even got these, I don't know. I know it was not common to see these on E46 BMWs unless you were in Europe.

  6. #6
    Join Date
    Oct 2015
    Location
    Charlotte, NC
    Posts
    1,193
    Charlie,
    This is a high quality DIY. I am not surprised, because all of your procedures are very detailed and clear.
    This is a great mod for sedan folks!

    Sent from my SM-G960U using Tapatalk

  7. #7
    Quote Originally Posted by RUS_ZHP View Post
    Charlie,
    This is a high quality DIY. I am not surprised, because all of your procedures are very detailed and clear.
    This is a great mod for sedan folks!
    Also a great mod for coupes as I have listed the coup specific part in my DIY as well

    Thanks Sergy!

  8. #8
    I have had this retrofit in my 330i ZHP for just over a year now and have to say this is one retrofit other than my M3 gauge cluster that I use all the time. I go to work very early in the morning when people are still running with their headlights on and in some cases have their high beams on. Having the rear sun shade does not fully eliminate the glare from oncoming headlights but they reduce it to where the high beam glare is not nearly as bad. I also like having it extended on hot sunny days as it seems to provide adequate shade to the interior and rear parcel shelf. It's a shame this option was not available here in the US when these cars were being sold however with that said the actual retrofit process is not difficult as I have shown in this DIY.

    Given a choice if I had to do this retrofit again, I would say hell yeah. Obtaining the necessary parts was not too expensive thanks to eBay and I found that the actual install was not too difficult. Just a little time consuming but overall not difficult to accomplish. Having this to me is priceless for what you get.

    The feedback I get from friends I have working at my dealer is that when they see my ZHP in for service they can tell it is mine just by the BBS CH wheels and rear sunshade my ZHP has. They have told me they don't see any E46 3-series sedans with rear sunshade but mine so it's nice having made my ZHP more unique.

Similar Threads

  1. Was there ever an OEM side sun blind option for sedan rear door windows?
    By nextelbuddy in forum General -- ZHP Related
    Replies: 46
    Last Post: 10-06-2022, 06:12 PM
  2. Replies: 115
    Last Post: 08-31-2021, 07:41 PM
  3. Fs: Testing waters E46 rear sunshade blind $400
    By Tnhl1989 in forum Classifieds
    Replies: 7
    Last Post: 04-16-2019, 07:18 PM
  4. E46 Complete Sedan Power Rear Sunshade Kit and Complete PDC Retrofit Kit
    By nextelbuddy in forum ZHP-Related Parts & Accessories (no vehicle sales)
    Replies: 27
    Last Post: 06-30-2017, 08:24 PM
  5. How To: Adjust Your Mirrors to Avoid Blind Spots
    By Rovert in forum General -- ZHP Related
    Replies: 41
    Last Post: 03-02-2012, 09:16 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •