PDA

View Full Version : Checking and Replacing front Control Arms and Bushings doityourself



3ZHP
09-01-2012, 08:55 PM
Instructions for Checking and Replacing front Control Arms and Bushings on a BMW E46

Pictures in this instruction are from a 2003 330I with ZHP Performance Package and may not look like others in the E46 family but should use the same procedure. This procedure references the passenger’s side of the car and has a headlight leveling bracket; the driver’s side does not.

Raise the vehicle with and appropriate jack and place a Jack Stand under the frame rail for safety. The image below shows the control arm and the control arm bushing. The Ball Joints are the two forward mounting points and the control arm bushing is the piece on the rear side attached with 2 hex head bolts.

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/02_ZHPContArmRep.gif

Checking the Ball Joint
Once the car is suspended from the frame with no support under the Control Arm grasp the rotor at the 2 O-Clock and 7 O-clock positions and turn it back and forward. There should be no movement in a good ball joint. The Video below shows the movement of a bad ball joint. Note; from a jack point of view, a second person watching for movement may be helpful.


http://youtu.be/kuOvH4Z6mDY

Removing the Lower Control Arm and Control Arm Bushing
Remove the (7) Philips screws (not shown) that attach the cover between the front bumper and the front cross member under the car. It’s not necessary to remove it completely and I just let it hang.

Loosen the 13mm nut in the center of the control arm (also pictured). Loosen the nut until you can no longer see the bolt threads. Now use a hammer on that same nut in an upward motion to dislodge the bracket from the control arm. This is a very tight fit and mine did not move until significant blows of the hammer finally mover it. Once dislodged remove the nut and tuck the bracket up and out of the way.

Remove the two attachment bolts from the Control Arm Bushing and leave it lay.

Remove the Ball Joint nut that attaches to the spindle (wheel side pictured below) using an 18mm box wrench (using a socket seems to have a clearance issue with the ABS sensor). I also included a picture of what I needed to do because of a stubborn bolt. The Allen Wrench show was to stop rotation of the ball stud.

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/09_ZHPContArmRep.gif

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/04_ZHPContArmRep.gif

This step to remove the nut from the Ball Joint that attaches to the frame is the most difficult step of the procedure. This is a 21mm nut and a 3/8 Drive Socket is not readily available. There’s not enough room to fit that big of a tool into this space either. Solution; a 13/16 inch socket is a near exact conversion to 21mm so, that and a short flex head ratchet should do the job. Note: this is torqued tight and takes some mussel to get broken loose. You will also only get one or two clicks of the ratchet so plan to be there for a while. Note: the picture below was taken with a camera from a spot your head will not fit into, prepare to work in the blind.

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/03_ZHPContArmRep.gif

To remove the control arm from the car you need to dislodge the ball joints. This can be done using a Pickle Fork and a hand sludge hammer (pictured below). You need to set the Pickle Fork wedging it between the ball Joint and the spindle (pictured below). Give it a few taps to engage it. Once in place give the Pickle Fork end several hard blows until separation occurs. A length of 2 x 4 lumber can be handy for keeping the strut assembly out of the way after the Ball Joint is free. Repeat procedure on the engine cross mount Ball Joint. It should take lees force to remove.

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/05_ZHPContArmRep.gif

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/10_ZHPContArmRep.gif

Reassembly

To make life simple the Control Arm Bushing should be attached to the control arm prior to installation. This bushing is a very tight and its sticky rubber so, lubrication helps. Sounds good but, its rubber and it reacts to petroleum so, DO NOT USE OIL, GREASE OR ANY PETROLEUM PRODUCT, unless you want to do this again when the bushings swell. The alternative method is soap and what was suggested to me by a BMW Tech was window cleaner. Sprayed it on the control arm then both sides of the bushing and smacked it into place with a rubber mallet.

Reassemble the Control Arm Assembly into the car buy slipping the bushing end into the pocket then the center Ball Joint in to its respective hole. Hand thread the nut onto the Ball Joint to keep it in place. Next reattach the Control Arm Bushing and tighten both screws till it’s seated. There should be no gap below and the recesses on the face (counter bores) should be fully engaged with the protrusions around the I.D. thread (Bosses). Reattach the Headlight Leveling Bracket and the outer Ball Joint. The last thing to do is tightening everything up. There are Torque specks for this but good luck getting a torque wrench in to do that. Use your best judgment on tightening.

Hope this helps and Happy Motoring,

-3ZHPGUY-

danewilson77
09-02-2012, 04:02 AM
Great read. Thanks for contribution.

Sent from Williamsburg, VA USA

echo46
09-02-2012, 04:34 AM
Excellent stuff, I am coming up on this job within the next 20,000. Did you replace with stock BMW ZHP control arm or is there something better?

3ZHP
09-02-2012, 06:11 AM
Yes, I used BMW parts. I've always been very satisfied with the factory suspension and limited my risk of change.

danewilson77
09-02-2012, 08:15 AM
Yes, I used BMW parts. I've always been very satisfied with the factory suspension and limited my risk of change.

Ok...so you got ZHP control arms and not stock E46 control arms.

Sent from Williamsburg, VA USA

echo46
09-02-2012, 08:26 AM
Yea? The ZHP arms are a bit different than the stock arms.

danewilson77
09-02-2012, 09:46 AM
Yea? The ZHP arms are a bit different than the stock arms.

Right.

3ZHP
09-02-2012, 10:43 AM
Ok...so you got ZHP control arms and not stock E46 control arms.

Sent from Williamsburg, VA USA

Yes they are ZHP control arms. When I talked to Tom the parts manager at Ganley BMW, he just ask for the last 5 of my vin to male sure everything was right. I must say that he went far beyond my highest expectations.

let me enplane, I called Tom a month and a half ago, he ask me for the last 5 or 6 numbers of my vin ans said it would take a little bit of time and he'd call me back. He call ed back within a few hours with a price and I said I'd get back with him. I checked a few of the online parts houses and the numbers were very close but I didn't have the money so, I just left it. Then a few weeks ago, I needed to be back in the in Cleveland for work and took the option to drive rather than fly. Because the arms were so bad we took the 330I vert instead but a few days before I left I called Ganley BMW parts department and said I would be in town, so could you order the parts. Response; sure, watts that last 5 of the vin. I told him, and never called back. When I arrived a week ago Friday 10 days after my call, they took great care of me with everything there at the quoted price and even carried it out to the car for me. It just doesn't get any better than that.

3ZHP
09-02-2012, 10:10 PM
Very interesting find, you have to check this out.


Its been said that the ZHP suspension is the same as the Sport Package and from what I found, that may be a false statement.

Friday before I started on changing out the control arms on the ZHP we ran into town with the wives 2006 330I Vert with the Sport Package. When I started the car the Brake wear sensor light came on so, that was today's project. Very interesting find when I looked at the control arms. They look very similar but the Sport does not have the ///M sticker with the part number on it and the forging stamp is different. Also, when I checked the Brakes she only needs fronts and the backs have over 1/2 of the pad left. On my ZHP they wore-out at the same time.

Is there something more here that we have yet to find out?

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/IMG_8872.gif

ZHP

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/IMG_8871.gif

Sport Package

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/IMG_8872_2.gif

ZHP

http://i591.photobucket.com/albums/ss351/3zhpguy/ZHP/Maintenence/IMG_8870.gif

Sport Package

3ZHP
01-09-2014, 10:29 AM
You may find some of your answers in this thread about front control arms.


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1)