FRONT PLATE

[xtremecro]

Ok so i have been searching around for past few days. i have the plate on my 4d mounted from dealer. Can you offsetted guys chime in with what you use? i kinda dont want to drill..

[az3579]

No-holes license plate holder:

http://gominigo.com/NHLPB-BMW.html

[billschusteriv]

That's the one! Cheaper there than most if not all other sites. Shipping is a little pricey... but it arrives quickly and packaged well.

Excellent construction... stainless steel. Very easy to install.

[danewilson77]

Also can check DDMTuning.com

[az3579]

Also can check DDMTuning.com

That was actually the first site I checked for a link, but I found it incredibly difficult to find what I wanted to see...

[cakM3]

No-holes license plate holder:

http://gominigo.com/NHLPB-BMW.html

botond,
I ordered my set for the ZHP today. thanks for the link :thumbsup

[thesixsins]

How far out does the plate stick from the bumper? Can anyone take an above angle shot?

[billschusteriv]

How far out does the plate stick from the bumper? Can anyone take an above angle shot?

This is with the euro bracket. It is preeeetty close. There is a rubber grommet to prevent the bracket from hitting the bumper.

http://i934.photobucket.com/albums/ad185/bill_schuster/IMG00033-20110521-1505.jpg

I also ordered the standard bracket but did not install.

Dane has the kit too... his sticks out a leeettle beet farther... not sure what size tow hook bolt adapter he got...

http://i1015.photobucket.com/albums/af278/nicee46/Imola%20Bimmer/DSC04097.jpg

I got the 30-35mm kit based on the measurement instructions on the gominigo website.

[xtremecro]

^ im sorry i dont seem to understand. where is the top picture bracket from

[az3579]

This is with the euro bracket. It is preeeetty close. There is a rubber grommet to prevent the bracket from hitting the bumper.

http://i934.photobucket.com/albums/ad185/bill_schuster/IMG00033-20110521-1505.jpg

I also ordered the standard bracket but did not install.

Dane has the kit too... his sticks out a leeettle beet farther... not sure what size tow hook bolt adapter he got...

http://i1015.photobucket.com/albums/af278/nicee46/Imola%20Bimmer/DSC04097.jpg

I got the 30-35mm kit based on the measurement instructions on the gominigo website.


I don't understand how y'all with the 3x-mm kits can get away with it.. the bumper is curved enough to cause interference with the plate, no? The way I measured it, I would have to get the 8x-9x-mm kit for the plate to clear the bumper...

How on earth could I have measured it wrong??? That's what the ruler said...

[cakM3]

Botond posted the link to the gominigo.com website earlier in this thread (post #2) so I ordered the 30-38mm kit from gominigo.com. Turned out this kit worked perfectly for my ZHP :thumbsup Props to Botond for the link :rockon

The kit from the shipping box:
http://i395.photobucket.com/albums/pp37/macdctr/Pic2-2.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic8-1-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic13-1-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic12-1-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic19-2.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic20-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic17-1.jpg

I like it :)

[billschusteriv]

I don't understand how y'all with the 3x-mm kits can get away with it.. the bumper is curved enough to cause interference with the plate, no? The way I measured it, I would have to get the 8x-9x-mm kit for the plate to clear the bumper...

How on earth could I have measured it wrong??? That's what the ruler said...

The measurement is just from where the shoulder of the tow hook sits to the opening in the bumper. You don't need to account for the entire curvature of the front bumper.

[billschusteriv]

^ im sorry i dont seem to understand. where is the top picture bracket from

Both brackets are the "no holes" license plate brackets. The one in the top picture is for a euro plate. I don't need to run a front license plate in my state.

[billschusteriv]

Botond posted the link to the gominigo.com website earlier in this thread (post #2) so I ordered the 30-38mm kit from gominigo.com. Turned out this kit worked perfectly for my ZHP :thumbsup Props to Botond for the link :rockon

The kit from the shipping box:
http://i395.photobucket.com/albums/pp37/macdctr/Pic2-2.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic8-1-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic13-1-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic12-1-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic19-2.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic20-1.jpg

http://i395.photobucket.com/albums/pp37/macdctr/Pic17-1.jpg

I like it :)

Nice pics Charlie! Really shows the standoff distance from the plate to the bumper well.

I'm glad you like it! It really looks good.

[cakM3]

Thanks Bill!

Yeah, I wanted to show everyone the kit and distance from the plate to bumper so there wouldn't be any questions for anyone else. :thumbsup

[DeM3n]

Nice pics Charlie! Really shows the standoff distance from the plate to the bumper well.

I agree. Almost gives it a sorta "3D" look.

[danewilson77]

I agree. Almost gives it a sorta "3D" look.

Mine's 4D.

[az3579]

Mine's 4D.

5D here.

Sent from my DROIDX using Tapatalk

[kayger12]

Mine's invisible:ninja

[cakM3]

:^)

[johnrando]

Mine is a black hole.