PDA

View Full Version : FS: (4) Apex ARC-8 wheels, 18x9.5 ET35, Matte Bronze


bimrologist
07-27-2020, 11:59 AM
Sold to a local buyer, thanks!
jtamayo027
07-27-2020, 12:25 PM
Interested

Sent from my SM-G970U using Tapatalk
rguti153
07-27-2020, 02:31 PM
[emoji44][emoji848][emoji848][emoji848][emoji848] tempting

Sent from my SM-G988U using Tapatalk
KendrickC
07-27-2020, 03:57 PM
Offtopic, what's your caliper setup?

Are they the BMW Performance calipers refinished?
bimrologist
07-27-2020, 05:09 PM
Offtopic, what's your caliper setup?

Are they the BMW Performance calipers refinished?

Bought a complete set of 135i sport calipers from LKQ and had them powder coated with Prismatic Powders chartreuse sherbert. Same setup I had on my Imola car here. http://www.zhpmafia.com/forums/showthread.php?21207-FS-2004-ZHP-Sedan-6MT-Imola-Alcantara-11-500
Vas
07-27-2020, 06:21 PM
Glws.

Btw got another zhp?

Sent from my Pixel 4 XL using Tapatalk
bimrologist
07-27-2020, 08:00 PM
Glws.

Btw got another zhp?

Sent from my Pixel 4 XL using Tapatalk

Yeah, this makes number 5. I had to have an M5, reason for selling the Imola car and then wished I had it back every day since. I tell myself every day I’ll never sell this one!
ZHP_Brandon
07-27-2020, 08:45 PM
Yeah, this makes number 5. I had to have an M5, reason for selling the Imola car and then wished I had it back every day since. I tell myself every day I’ll never sell this one!

What was your experience powder coating these?

Did you go for a rebuild at the same time and upgrade the pistons? What rebuild kit did you use if so? I got a set just like this a few months back (Front and Rears) and bought the powder from prismatic as well and I’ve been so hesitant to move forward.

This is what the seals/pistons look like, Idk if the phelonic pistons look any different to standard ones [emoji28]https://uploads.tapatalk-cdn.com/20200728/41dd6004f9c9607ca88ef3ff9e25ae13.jpg


Sent from my iPhone using Tapatalk
sillieidiot
07-28-2020, 01:01 AM
Can we get some pictures from a 3/4 view? the face looks strangely flat for a profile 3 wheel.
bimrologist
07-28-2020, 06:57 AM
What was your experience powder coating these?

Did you go for a rebuild at the same time and upgrade the pistons? What rebuild kit did you use if so? I got a set just like this a few months back (Front and Rears) and bought the powder from prismatic as well and I’ve been so hesitant to move forward.

This is what the seals/pistons look like, Idk if the phelonic pistons look any different to standard ones [emoji28]https://uploads.tapatalk-cdn.com/20200728/41dd6004f9c9607ca88ef3ff9e25ae13.jpg


Sent from my iPhone using Tapatalk

I rebuilt the calipers after they were powder coated with Stoptech stainless pistons and centric seal kits. I'm not a powder coater so I'm not sure what you mean by moving forward with powder coating?
bimrologist
07-28-2020, 07:00 AM
Can we get some pictures from a 3/4 view? the face looks strangely flat for a profile 3 wheel.

They look flat because all of those photos are from straight on to highlight the wheel and show that there's no damage.

36934
Showda711
07-28-2020, 05:47 PM
How's the fitment? Spacer or rolling the fender needed to avoid rubbing?
bimrologist
07-29-2020, 06:00 AM
How's the fitment? Spacer or rolling the fender needed to avoid rubbing?

They fit flush in the front, no rubbing at all. Rear fenders are rolled and bumper brackets are trimmed, it rubbed on the fender between 11 and
1 o'clock until I got the ride height figured out, but now it's clean and smooth. Not sure about factory suspension or lowering springs as I'm on
coilovers.